In the spirit of going out to listen to the song and returning home to the plane, so many years to accompany the landlord can be counted as a HiFi plug, which is the headset bar, ie80. Although the bar is good, but after listening to so many years will inevitably be boring, in addition to 80 no wire control, this song for the mobile phone songs, pause must be out of the phone, really quite inconvenient. Then I wanted to be able to stick to a standard 80 but wired control plug. Find a circle on the Internet, and finally selected 1more four-ring iron e1010, the main reasons are several: one to the landlord from the plug to the big ears are dynamic, have not heard the taste of moving iron, want to enter one; According to some hearing tests, e1010 is mainly a popular tune. This is just a supplement to the 80 classical tuning. The last is the price. Although the price of an East is 1299 in the four-unit ring, it is a fish. The new unopened (with ticket) price is less than 800, which is more cost-effective.
1MORE four-ring iron headphones E1010 three moving iron dynamic HIFI fever sound field open 1299 yuan Jingdong to buy 
Packaging and workmanship: Before you understand, 1more has always been more luxurious in this regard, as shown in the figure. Hard shell packaging + rich accessories (especially like leather) can really make people feel like buying accessories to send headphones. The workmanship of the headset should be very refined, and the metallic material has a Japanese bias. There are two maximum slot points: one cannot change the line. Because the previous generation of ring irons can be changed, this kind of design that cannot be changed is a bit unjustified. Another is the clips in the accessories: This is definitely a pit father ** design, the landlord tried the next can not be used, far less than the 5 hair a traditional clip practical.
Wire part: It's not bad, it's a bit longer than IE80's, and it's also a lot softer. I hope winter won't become wire like 80.
Wear, sound insulation, stethoscope effect: wear better than expected, because it is a metal material, weight is a little heavier than ie80, plus cable control and traditional wear, certainly not around the ears of ie80 strong, but usually normal out of the street is also very stable No worry about sliding. Ie80 is a closed design, can achieve the effect of passive noise reduction 26 decibels, and E1010 should be considered open, basically no sound insulation effect. Since it is not worn around the ear, the stethoscope will have a little more than 80, but it is not obvious, and the influence on the street is relatively small.
Compared with ie80's listening: In order to fully tap the potential of the two headsets, directly serve the two goods with the HD800 server.
Tri-band distribution: Compared to the triple-frequency of the 80 middle concave, the energy distribution of 1more's E1010 tri-band is more balanced and should belong to the straight barrel type tri-band distribution.
High School Low Frequency: The low frequency is less than 80, but the volume is still relatively large. The dive is generally good. Listening to the “River†feels very obvious; the vocal frequency of the intermediate frequency is generally closer to the 80 and can better put the low frequency and people. The sound is separated, but this nearness differs from song to song. The overall density of the sound is not bad, and it can provide enough atmosphere for the popularity. How to say high frequency, there are still old problems. Since the high frequencies are mainly musical instruments, although the resolution of moving iron is better than that of 80, it is still more scratching, but it is still not as smooth as 80, and the sense of hearing is not so beautiful. Fortunately, it can't be said to be exciting.
Sound field, transparency: Thanks to the open design, the permeability is better than the ie80, 80 is criticized is not transparent. The sound field is less exaggerated than 80, but it is enough. The momentum is certainly not as good as 80. But the problem is that this sound field is weird. There is a feeling that the boundary of the sound field is distorted. It is better to listen to a nearby instrument. It is less natural if the instrument is located far away.
Analysis, Conclusion: The overall analysis and conclusions are better than 80, after all, moving the iron. However, some songs will be better because of the high-frequency analysis and scratching the ears, but they will have a lot of attention.
Dynamics, Transients: Transients don't really hear good or bad, dynamic general feelings. In this regard, I should be considered wood after all.
Cost-effectiveness: One is made in China, and the other is Germany. So it's more fair to compare Dea and BNM. In fact, the price is similar. But considering the price of less than 800 in a fish, it should be said that it is very good value.
Thrust: Compared with the ie80's 16 Euro 126dB, the 99dB of the E1010 requires a larger volume setting to achieve the same sound pressure, which may be somewhat stressful for some weaker mobile phones.
to sum up
In general, if this headset is regarded as a standard, it should be considered as both a sense of quality and a sense of quality. However, there may be more people to choose 1more's four-unit ring. On the one hand, it is more popular to listen to popular, and secondly, 80 is the kind of earphone that will take a long time, and the overall tuning of E1010 is more modern. The design is also more suitable for young people's tastes.
OPT Diamond Cutting Tools Co., Ltd provide a variety of carbide milling inserts, they were widely used to cutting steel, stainless steel, cast iron, heat-resistant alloys, non-ferrous material and hardened material.
Carbide milling inserts are used in the machining industry. Carbide milling inserts of different materials are used depending on the processing of different metal (non-metallic) materials.
Advantage:
Various
grade and size are available.
Long use lifetime
and stable performance.
Good quality with competitive price.
Flexible in order quantity:
Samples can be provided before mass production, and MOQ can be discussed accordingly.
PRODUCT DETAIL:
PAYMENT AND DELIVERY:
PRODUCT EQUIPMENT :
+
ABOUT US :
We are specialize in manufacturing PCD diamond tools and Carbide tools. Our major product inclulde PCD Inserts , PCD Reamers , PCD End Mills, PCD Taps, Cabide Inserts,Carbide Drills, Carbide Reams, Taps etc.,
We also offered customized cutting tools per drawings, and provide package according to customer requirements. We manufacture a series range of cutting tools for machining of Cast iron, Aluminium alloy and Non-Ferros metal, it is widely used in all major sectors like Automobiles, Engineering, Aerospace, Aviation and 3C industry. Premium quality of raw material is used in the production and strict examination during processing with advanced equipment, so our client are satisfied with our reliable quality and on-time delivery.
Our best selling of cutting tools include PCD Inserts, PCD End Mill, PCD Ball Nose Mill, PCD Reamer, Carbide Taps, Carbide End Mill, Special Form Cutter and many more. For these years we have been made a large forward in the technologies of manufacturing cutting tools. With high quality on performance and price, our product sells well both on domestic and overseas market. And we will always focus on the quality and best service, to make long business relationship.
quanlity control:
We have dedicated team of quality control and precise equipment to keep good and stable performance for our products and processing services.
Carbide Milling Inserts,Lathe Cutting Inserts,Solid Carbide Milling Cutters,Carbide Milling Tools
OPT Cutting Tools Co., Ltd. , https://www.optdiamondtoolss.com